Melola Discovery

← Melola Discovery

Jurnal SINTA 1

The Effect Of Heating Temperature On The Hardness, Microstructure And V-Bending Spring Back Results On Commercial Steel Plate

Journal of Applied Engineering and Technological Science (JAETS) · Vol. 1 No. 1 (2019) · hlm. 1–16

DOI
10.37385/jaets.v1i1.10
ISSN
2715-6079, 2715-6087
Terbit
2019-11-30
Penerbit
Yayasan Riset dan Pengembangan Intelektual (YRPI)
Bahasa
en

Abstrak

The need for low carbon steel plate sheets with relatively thin thickness measurements in Indonesia is currently quite high, especially in supporting the automotive industry, the electronics industry, the food industry, beverages, and household appliances. To fulfill this, raw materials for low carbon steel plate sheets that have high formability and are not easily cracked in critical areas of the desired model are required. For this reason, research on the effect of temperature variations in heat treatment on hardness, microstructure and spring back of V-bending results on steel plates with a plate thickness of 0.8 mm. The research method used was a laboratory experimental method. The heat treatment is carried out with temperature variations of 710, 820 and 9300C with a holding time of 60 minutes. Tests carried out on specimens are hardness testing, microstructure testing, and spring back V-bending results on steel plates. The results of this study indicate a decrease in the spring back angle where the smallest spring back angle in the bending process is on the 9300C plate which is 1,040. The value of the hardness results from V-bending has increased significantly. The increase in the value of hardness because the plate has an atom shift or dislocation by shear stress (slip) due to plastic deformation on the plate. The highest hardness value is on the 7100C plate which is 154.67 HV or has an increase of 14,291% of the pre-bending plate. The lowest hardness value is on the 9300C plate which is 125.33 HV, its hardness increases 4.4% against the pre-bending plate. Heat treatment also causes changes in the microstructure of the plates from the process of regulation and reshaping of crystals to the growth of new grains which have implications for changes in mechanical properties and formability of the workpiece.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 121 tautan kepenulisan bersama · 7 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Halu Oleo
  • Politeknik Negeri Ketapang
  • Hasanuddin University
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Yusuf YusufUniversitas Halu Oleo4
Isalman IsalmanUniversitas Halu Oleo2
Endro SukotjoAfiliasi tidak diketahui2
Muhammad TaufikUniversitas Halu Oleo2
Nofal NurUniversitas Halu Oleo1
Cahya Dwi SaputraUniversitas Halu Oleo1
Agustinus TangalayukUniversitas Halu Oleo1
Nasrul NasrulUniversitas Halu Oleo1
Rahmat MadjidUniversitas Halu Oleo1
Nurul Artika Putri TUniversitas Halu Oleo1
Hartini HartiniUniversitas Halu Oleo1
Alida PalilatiUniversitas Halu Oleo1
Retno Sefianty MajidUniversitas Halu Oleo1
Ansir AnsirUniversitas Halu Oleo1
Darnawati DarnawatiAfiliasi tidak diketahui1
Awaluddin AwaluddinHasanuddin University1
Samdin SamdinAfiliasi tidak diketahui1
Nurwati NurwatiAfiliasi tidak diketahui1
Wahyuniati HamidAfiliasi tidak diketahui1
Alida PalilatiAfiliasi tidak diketahui1
Hasnani HasnaniAfiliasi tidak diketahui1
Nursaban Rommy SulemanAfiliasi tidak diketahui1
Adnan HakimAfiliasi tidak diketahui1
Andi Azwar Anas IdrisAfiliasi tidak diketahui1
Sri Wiyati MahraniAfiliasi tidak diketahui1
Laode Rahmat MalbarAfiliasi tidak diketahui1
Juharsah JuharsahUniversitas Halu Oleo1
Valentinus Amstrong TNUniversitas Halu Oleo1
Jumatin JumatinUniversitas Halu Oleo1
Hartini HartiniUniversitas Halu Oleo1
Hasnawati HasnawatiUniversitas Halu Oleo1
Isalman IsalmanAfiliasi tidak diketahui1
Muhammad MasriAfiliasi tidak diketahui1
Isra SyamAfiliasi tidak diketahui1
Eriyadi EriyadiAfiliasi tidak diketahui1
Ibnu HajarAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.yrpipku.com/index.php/jaets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">The Effect Of Heating Temperature On The Hardness, Microstructure And V-Bending Spring Back Results On Commercial Steel Plate</dc:title>
	<dc:creator xml:lang="en">Ruchiyat, Asep</dc:creator>
	<dc:creator xml:lang="en">Anhar, Muh</dc:creator>
	<dc:creator xml:lang="en">Yusuf, Yusuf</dc:creator>
	<dc:creator xml:lang="en">Polonia, Betti Ses Eka</dc:creator>
	<dc:subject xml:lang="en">Sheet Metal Forming, V-Bending, Springback, Annealing, Microstructure</dc:subject>
	<dc:description xml:lang="en">The need for low carbon steel plate sheets with relatively thin thickness measurements in Indonesia is currently quite high, especially in supporting the automotive industry, the electronics industry, the food industry, beverages, and household appliances. To fulfill this, raw materials for low carbon steel plate sheets that have high formability and are not easily cracked in critical areas of the desired model are required. For this reason, research on the effect of temperature variations in heat treatment on hardness, microstructure and spring back of V-bending results on steel plates with a plate thickness of 0.8 mm. The research method used was a laboratory experimental method. The heat treatment is carried out with temperature variations of 710, 820 and 9300C with a holding time of 60 minutes. Tests carried out on specimens are hardness testing, microstructure testing, and spring back V-bending results on steel plates. The results of this study indicate a decrease in the spring back angle where the smallest spring back angle in the bending process is on the 9300C plate which is 1,040. The value of the hardness results from V-bending has increased significantly. The increase in the value of hardness because the plate has an atom shift or dislocation by shear stress (slip) due to plastic deformation on the plate. The highest hardness value is on the 7100C plate which is 154.67 HV or has an increase of 14,291% of the pre-bending plate. The lowest hardness value is on the 9300C plate which is 125.33 HV, its hardness increases 4.4% against the pre-bending plate. Heat treatment also causes changes in the microstructure of the plates from the process of regulation and reshaping of crystals to the growth of new grains which have implications for changes in mechanical properties and formability of the workpiece.</dc:description>
	<dc:publisher xml:lang="en">Yayasan Riset dan Pengembangan Intelektual (YRPI)</dc:publisher>
	<dc:date>2019-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.yrpipku.com/index.php/jaets/article/view/10</dc:identifier>
	<dc:identifier>10.37385/jaets.v1i1.10</dc:identifier>
	<dc:source xml:lang="en">Journal of Applied Engineering and Technological Science (JAETS); Vol. 1 No. 1 (2019): Journal of Applied Engineering and Technological Science (JAETS); 1-16</dc:source>
	<dc:source>2715-6079</dc:source>
	<dc:source>2715-6087</dc:source>
	<dc:source>10.37385/jaets.v1i1</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.yrpipku.com/index.php/jaets/article/view/10/2</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2019 Journal of Applied Engineering and Technological Science (JAETS)</dc:rights>
</oai_dc:dc>